Conducted Output Power Test Report: FCC Part 15.247 & ISED RSS-247

FCCPart15C&ISED2.4GWIFI 31-40

This document presents the test results for conducted output power measurements performed on a wireless device. The tests were conducted to ensure compliance with the regulations outlined in CFR 47 FCC Part 15 (specifically section 15.247) and ISED RSS-247 ISSUE 3. The primary objective was to verify that the device's output power remains within the limits specified by these standards.

The testing methodology involved placing the Equipment Under Test (EUT) on a table and configuring it to operate in transmitting mode. The antenna was then disconnected, and a low-loss RF cable was used to connect the antenna port to a power sensor. Measurements were taken for each channel, utilizing a peak detector for peak power readings and an AVG detector for average power readings. The results, presented in tabular format, include the antenna used, frequency, peak power, conducted limit, EIRP, EIRP limit, and verdict (pass/fail).

The test setup followed a block diagram configuration consistent with section 8.1 of the report. The results indicate that the device successfully meets the conducted output power requirements of both FCC and ISED standards across various operating modes (11B, 11G, 11N20MIMO, and 11N40MIMO) and antenna configurations.


File Info : application/pdf, 10 Pages, 4.12MB

Download

tags: ["FCC Part 15.247", "ISED RSS-247", "11B", "11G", "11N20MIMO", "11N40MIMO", "JCF250408041-001"]
Array
(
    [0] => Array
        (
            [url_sha] => d234469980ef7dc3c07cbe22c383e5a63d9ab8d37b01678bee3903f25880764d
            [source] => fccid
            [url] => https://apps.fcc.gov/eas/GetApplicationAttachment.html?id=8262915
            [href_text] => FCCPart15C&ISED2.4GWIFI 31-40
            [href_description] => EXPRESS LUCK INDUSTRIAL (SHENZHEN) LIMITED ELRT8192FCT IEEE 802.11b/g/n 2T2R USB Wi-Fi Module 2AWY6-ELRT8192FCT 2AWY6ELRT8192FCT elrt8192fct
            [http_status] => 200
            [http_lastmod] => 0000-00-00 00:00:00
            [http_contenttype] => 
            [http_filename] => GetApplicationAttachment.html?id=8262915
            [http_size] => 4321382
            [file_sha256] => c82d2b523e42ff1c4223daff82d3c51a6243e1348ad68d2f1d2b1d83a7211563
            [domain] => document.fccid
        )

)
Array
(
    [file_sha256] => c82d2b523e42ff1c4223daff82d3c51a6243e1348ad68d2f1d2b1d83a7211563
    [cleanFccId] => 2AWY6ELRT8192FCT
    [title] => Conducted Output Power Test Report: FCC Part 15.247 & ISED RSS-247
    [description] => This report details the conducted output power measurements for compliance with FCC Part 15.247 and ISED RSS-247 standards. Testing procedures and results are included.
    [brand_name] => KEYSIGHT
    [keywords] => ["FCC Part 15.247", "ISED RSS-247", "11B", "11G", "11N20MIMO", "11N40MIMO", "JCF250408041-001"]
    [intro] => 

This document presents the test results for conducted output power measurements performed on a wireless device. The tests were conducted to ensure compliance with the regulations outlined in CFR 47 FCC Part 15 (specifically section 15.247) and ISED RSS-247 ISSUE 3. The primary objective was to verify that the device's output power remains within the limits specified by these standards.

The testing methodology involved placing the Equipment Under Test (EUT) on a table and configuring it to operate in transmitting mode. The antenna was then disconnected, and a low-loss RF cable was used to connect the antenna port to a power sensor. Measurements were taken for each channel, utilizing a peak detector for peak power readings and an AVG detector for average power readings. The results, presented in tabular format, include the antenna used, frequency, peak power, conducted limit, EIRP, EIRP limit, and verdict (pass/fail).

The test setup followed a block diagram configuration consistent with section 8.1 of the report. The results indicate that the device successfully meets the conducted output power requirements of both FCC and ISED standards across various operating modes (11B, 11G, 11N20MIMO, and 11N40MIMO) and antenna configurations.

)
Array
(
    [0] => Array
        (
            [id] => 8262915
            [file_sha256] => 
            [applicationId] => QGVTQ+FYJT2KgcDU7WqwKg==
            [description] => FCCPart15C&ISED2.4GWIFI 31-40
            [shortTermConfidential] => No
            [permanentConfidential] => No
            [supercede] => No
            [exhibitType] => Test Report
            [fileType] => Adobe Acrobat PDF
            [displayType] => pdf
            [fileSize] => 4321384
            [submissionDate] => 2025-05-06 00:00:00
            [dateAvailable] => 2025-05-06 00:00:00
            [creationDate] => 
            [producer] => 
            [modDate] => 
            [title] => 
            [creator] => 
            [author] => 
            [pages] => 
            [realSize] => 
            [html] => 0
            [png] => 0
            [txt] => 0
            [version] => 1
            [source] => 0
            [fccId] => 2AWY6-ELRT8192FCT
            [cleanFccId] => 2AWY6ELRT8192FCT
            [exif] => 0
        )

)